Showing posts with label RV Repair. Show all posts
Showing posts with label RV Repair. Show all posts

Monday, August 10, 2015

How to Replace RV Slide Topper Awning Fabric

How to Replace RV Slide Topper Awning Fabric 


Well, this was upsetting.  The wind caught our awning and ripped the fabric.....likely because it was so old and brittle.  But, still...upsetting.  

So, we ordered new fabric and this is how we did the install.....By the way, when measuring for new fabric, the fabric lengths are center to center, arm to arm.

This is for a slide topper awning compatible with Carefree, Carter, & A&E awnings.

We decided to prop the awning arms up at about chest level to make it easier to replace the fabric.


As you unroll the awning fabric, note the number of times you turn the torsion assembly to relieve the tension.  The spring’s tension is exact and will need to be set to this exact point during reinstallation.  In our case, the awning fabric had ripped off, so we guessed 11 times.  Keep in mind that unrolling the fabric tightens the spring and rolling it up releases it.

Hardware will need to be removed only from the side that you will be inserting the awning fabric from.  The rivets (example shown below) have to be removed...


...as well as the awning bracket.


There was also a screw down the track from the bracket that needed to be removed.  It actually had to be drilled out.


When the rivets are removed, the torsion assembly can be pulled apart as shown below.  The cord can be pulled out as well as...


...the existing awning fabric.  Keep in mind that the fabric will be reinserted in much the same way as it is removed.



The next step requires the help of an assistant.  In fact, the help of 4 people would have been ideal, but we accomplished the task with just the two of us.  The vinyl awning fabric came with a cord installed on the bottom and top.  First, feed the cord and fabric into the top rail about 1 foot.


Then feed the cord and fabric into the track on the torsion assembly.  


This is where more people comes in handy as you feed the fabric into the track and keep guiding it down the rail.


The top and bottom need to be fed together.


When the fabric has been fed completely onto the track, the bracket and screw can be reinstalled.


The torsion assembly has a second track.  The fabric has to be carefully folded into this track and then a cord inserted into the track.  This is tricky.  You have to be careful not to rip the fabric.  We used a pin punch to glide the cord down the track.  We also sprayed WD40 on the fabric to make it easier to slide the cord down the track.


We used the blunt edge of a bondo applicator to fold the fabric down the track.


There was an existing stopper piece that we reinserted over the cord before pushing the torsion assembly back into place.


The existing rivets were old/worn, so we used sheet metal screws to hold everything in place.



Carefully roll the awning up into place.



The following are pictures of the awning fully extended.  We are very happy with this vinyl fabric.  It is also working well in the rain.



Yay!!  All finished.


My mom & Chad




 

Monday, January 12, 2015

How to Fix an RV Roof Leak - Part 2

Well, our RV roof leak saga continues lol.  Upon further investigation, Chad found what he thinks is the main culprit for the roof leak in the front of the RV.  It was the bathroom vent pipe pictured here...



He took the lid off and noticed that the pipe fit loosely in the hole.  So, he sealed it up good with white silicone. 

Today we had a nice rainy wintry mix.  So, we had a good opportunity to see how the fix worked.  Well, there was no water in the cabinets.  So, that is an improvement.  But, there is still a drip on the right side above the area where we keep our shoes.  So, we are well on our way to getting the problem completely fixed.




Saturday, December 20, 2014

How to Fix an RV Roof Leak - Part 1


Things are going well with our RV life.  We didn't get any rain inside the last time it rained, but it wasn't as bad as the previous storm.  Everything has dried out now and we did some research to see what we can do to stop our roof from leaking.  Chad checked everything over on the roof and couldn't find anywhere it looks like it could be leaking. But, we had to do something - cheap & fast.

We decided to try  Premier Wet & Dry Plastic Roof Cement.  It looks like black tar.  And, Chad and his dad used it to coat all of the roof perimeter, seams, and around any penetrations.  It's not pretty, but it was fast.  Time will tell if it actually works....


Coating around the perimeter
 
It's supposed to be another rainy week this week, so we will see how it all holds up.  We bought two cans which was just the right amount for our 30 ft. RV.  This product could also be used in our cold temperatures, so it was a good choice for us.  It's 28 degrees here right now.  In the Spring we will coat the entire roof with Premier Fibered Aluminum Coating which will insulate it and create a better seal.  That will hopefully be Part 2 of the roof leak fix.   You're supposed to wait a minumum of 30 days before you apply the aluminum coating.

Chad with his "gear" on to head up on the roof
Before he started coating the roof, Chad cut off the old TV antenna.  We don't even have a TV.  And, if we did decide to get one later, the antenna wouldn't be useful because they don't transmit signals like that anymore.


Cutting off the antenna

 
Apply with rubber gloves or a trowel




Monday, December 8, 2014

Roof Leak is back

We got slammed with so much rain Friday evening and continued all day Saturday.  And, unfortunately, the roof leak is back above the driver's area.  This time it was worse than the last time, it was dripping in at least two distinct spots.  We used towels to absorb all the water.  So, today Chad used white silicone again to try to seal up the leak. Unfortunately, he couldn't find any indication on the RV roof of any area that could be leaking.  So, he put white silicone along the whole seam in that area of the roof.


In the picture you can see the water spots the leak created.  The blankets are there because we created a blanket fort with them to create a weather seal to keep the cold out that pours in off the windows in the front of the RV.  (More about that later.)

By the way, the first roof leak we found is definitely not leaking.  So, that's good news.

Wednesday, December 3, 2014

How to repair exterior damage to an RV

Monday, Chad repaired the damage done to the underside of the RV from the snow plow mishap.  

Damage from the snow plow
The piece you see hanging down in the picture is rusted out metal square tubing.  So, Chad cut off the damaged section, shown here...


Next, he unscrewed the trim around the wheel so that he could access the area better.




He replaced it with a new piece of  steel square tube.  



He attached the two tubes by screwing a piece of flat rod to them.


On the other end, he attached the steel square tube to the wheel well.




Next, he screwed it to the fiberglass.



Then, he put the aluminum trim piece back on the underside of the RV.



He attached it with self-tapping screws .




Then, he used an aluminum trim piece along the length to cover the damage. (He attached it with screws.)



Last, he sealed all the seams with silicone to create a weather proof seal.